Vertex² User Manual · PDF pages 35–37

Web Server – CONFIG Section

[AUTOSWITCH INPUTS] When activated, the new TMDS / Pixel clock Auto switch feature will force the Vertex² unit to automatically switch to the active signal if the selected signal is lost. It can also auto switch source that keep sending +5V when in standby such as ATV4K, X1X, Shield and others.

[AUTOSWITCH PRIORITY] When input priority mode is enabled, as soon as a new active input is detected, Vertex² will switch to it.

[HDCP VERSION] Allow you to select/force the HDCP revision of the TX1 Output Port.

[HTPC MODE] Useful if you have trouble with windows display and icons when resuming from stand-by mode. Please note that with default firmware HTPC mode is not compatible with HDCP signal. You can set HTPC mode for each input individually.

[OLED DISPLAY] Enabled by default, Vertex² OLED display can be turned ON/OFF at will. Some users might found the Vertex² OLED display visually disturbing in their HT setup. You have the possibility to turn it off.

[ROTATE 180 DEG] OFF by default, based on your setup, you might prefer to flip the OLED display, once activated, this option will flip the Vertex² OLED.

[REVERSE COLORS] OFF by default, once activated this option will reverse the Vertex² OLED colors.

[OLED FADE] Allow you to define a custom timing in seconds before OLED FADE, set it to 0 for OLED to always stay active. Default is 30sec.

[OLED PAGE] Select the OLED page that will be displayed at startup .

[MUTE TX0 AUDIO] If you use an AVR at HDMI audio out, you might want to disable sound going to equipment connected at TX0 output. Here you can mute the TX0 output sound.

[MUTE TX1 AUDIO] If you use an AVR at HDMI audio out, you might want to disable sound going to equipment connected at TX1 output. Here you can mute the TX1 output sound.

[IR] You can globally turn ON or OFF IR support for Vertex²

[ANALOG L/R AUDIO CONTROL] This option will adjust the Analog Stereo output from this section. Volume, Bass and Treble control are available.

[SEND] After Volume, Bass or Treble values changes, click send to apply your changes.

[TEST PATTERN GENERATOR FOR TX0] Once configured with dropdown field and enabled, this option will display a test pattern at TX0 output. It can be useful for testing equipment. 480p60, 720p60; 1080p60, 4k24 or 4K60 resolution are available, Pattern can be color bars, ramp1 or ramp2 and HDCP can be set to none, 1.4 or 2.2

[IP CONFIG] This section allows you to edit the way Vertex² will retrieve its IP address. Any changes will only be applied after reboot (power cycle)

[DHCP] When set to ON, Vertex² will retrieve a dynamic IP automatically.

[mDNS] Set ON/OFF mDNS support for you router/network capabilities and security settings.

[CURRENT IP CONFIGURATION] Display the current value of IP address, IP mask and IP gateway and MAC address.

[CONFIGURE STATIC IP] Enter the IP address, IP mask and IP gateway of your choice for a static IP setup, DHCP needs to be OFF for using static IP values

[SET IP] After any changes in IP configuration, click SET IP to validate.

[IP PORT] Set the IP/telnet port of your choice here (default value is 2220).

[SET PORT] Click here to apply the IP/telnet port of your choice (Reboot or Power cycle required)

[REBOOT UNIT] Click REBOOT button to restart Vertex² completely.

[EXPORT CONFIG] Allow you to export a text file that includes the full list of Vertex² settings and some setup information that can be useful for support.

[ISSUE HOTPLUG] Click Send button to perform a soft-reset in your setup.

[CLEAR ALL SETTINGS TO FACTORY DEFAULTS] Type RESET in the factory def text field and click the available RESET button to clear all settings to factory defaults. Vertex² power cycle needed.

[EDID FACTORY SETTINGS] Click the available check box to clear all EDID settings to factory defaults and type RESET in the test field. Finally click the RESET button and unit EDID will be reset to factory defaults.

[FW UPDATE] Select the Vertex² firmware file and click SEND to upload it. Wait for Vertex² to reboot automatically, once Vertex² is rebooted, refresh the webserver page.

[REFRESH] Refresh the current page.